How to Make a Homemade Gravity Bong Easily

Bong Posts
How to Make a Homemade Gravity Bong Easily
Image source: YouTube

A gravity bong is a smoking device that can help you consume your herbs in one, massive hit. It’s made up of two containers, with one large enough for water and a smaller bottle to fit in. The materials can be made of plastic, or glass if you want to make something cleaner.

However, making your glass gravity bong requires specialized equipment such as glass cutters, clamps, and lathes. It also takes time to prepare. We’ll teach you how to make a homemade gravity bong using simple tools and materials that you can easily find in your home.

Materials for making the gravity bong

Here’s what you need to make a simple yet powerful smoking tool.

  • One 2-Liter water bottle and its bottle cap

  • A 1-gallon water bottle

  • Cutters

  • Scissors

  • Aluminum foil or steel mesh tea ball infuser

  • Large needle or unfolded paper clip


The size of this gravity bong is for big, serious rips. If you want something smaller, you can change the water bottles to a 1-liter and 2-liter respectively. Now, let’s go make your DIY gravity bong!

How to make a gravity bong




Before you begin, make sure that you have a wide, stable surface for creating your bong. You’re going to need force to cut the bottles.

  1. Get the bigger bottle and cut out the top, just below the shoulder.

  2. For the smaller bottle, cut out about an inch off from the bottom. Place the bottle inside the bigger one to check the height. Ideally, the lip of the inner bottle should be just an inch or two above the outer cylinder. Cut out a bit at a time to help conserve the bottle.

  3. Once you got the right height, you can get the other half of your steel mesh tea ball infuser as a bowl. If not, let’s prepare the cap.

  4. Take your cutter and score deep “X” at the middle of the cap. Get the scissors to widen the hole and create a gap.

  5. Take your aluminum foil and fold it to form a thick, full square. Place it on top of the cap and push it through the hole to create a bowl and then wrap it around the edge of the lid. If you don’t have a top, place the aluminum foil on the lip of your bottle and form an indentation inside the rim.

  6. Get your needle or paper clip and poke holes in the aluminum.

  7. Add water inside the big bottle until it reaches the neck of your inner bottle.

  8. Pack the herb on your makeshift aluminum bowl or the tea infuser.

  9. Insert the small bottle in your water vessel. Place your packed bowl or tea infuser on top of your small bottle.

  10. Get your lighter and fire up your herb. Lift the inner bottle slowly and watch your gravity bong milk your botanical. Don’t go too fast, or you’ll waste your herb. Don’t go too slow either to prevent your smoke from getting stale.

  11. Stop lifting before the bottle clears from the water.

  12. Take out the cap and place your mouth on the lip of the bottle. Push the gravity bong down and let it drive the smoke in your lungs.



What you should know about your DIY gravity bong


First things first, you should know how to use a gravity bong. Now that you’re done, let’s cover a few things that you have to know about homemade gravity bongs. They are inexpensive, and you can get the materials almost anywhere. However, make sure that you’re using clean, BPA free, food-grade materials. When you use non-food grade materials for your gravity bong, you expose yourself to harmful chemicals and toxins. Not only will that ruin the test of your expensive herbs. More importantly, this practice can land you to a hospital.

Don’t let all that massive amount of water fool you. A gravity bong gives seriously strong hits because of the lack of water filtration. Pulling from a bong is not the same as letting gravity drag the smoke down from the bowl. If you want to get some diffusion, you need to get a bubbler bowl, which is a 10-inch long pipe that reaches deep within the bong.

Use the gravity bong after you’ve experienced smoking a bong or a pipe. Beginners beware because the massive amount of smoke is too overwhelming for you to take in. Never take on the gravity bong unless you’re experienced smoking from other bulky smoking devices.

When you’re done smoking with your homemade gravity bong, throw all disposable pieces away. Do not reuse the bottles to prevent inhaling toxins, even if the material is BPA free.

One more important note is that a socket gravity bong takes a slightly different process.

Conclusion


Making a homemade gravity bong is easy, and it’s also fun to use. However, it has a limited lifespan because of the nature of the materials. If you want a long-lasting gravity bong, we highly recommend getting the Gravitron Glass Gravity Bong by GRAV. It’s made of an all-glass material for cleaner and safer smoking.

What's more, you get to taste the real flavor of your herb because you don’t have aluminum or metal interfering with the taste. Click here now and get your very own Gravitron.

13 comments

  • Dabpadzone-hitter14mm 45 Degree Tree Perc Ash CatcherThis is because the ash catcher would make your piece top-heavy, increasing the likelihood of an accident and breakage. On the contrary, massive bongs are usually paired with large ash catchers to keep the aesthetic consistent.

    nectar collecter
  • Dab Pads & Silicone Mats nectar collector We have secure servers and exchange zero customer information. The glass storage jar has 2.5 milimet thick sides and a super thick 7 milimet bottom. The glass has to be made to exact dimensions in order to for all the pieces to fit together correctly. .

    glass globe vaporizer
  • Bong Coasters & Bong Pads glow in the dark straw A one hitter dugout is one of the simplest ways to smoke legal herbs on the market. So while they are extremely convenient to use, the disadvantage is that it holds a relatively small amount of weed and needs to be refilled all the time if you tend to smoke frequently .

    west side smoke shop
  • Dab Pads & Silicone Matswax containers14mm 45 Degree Showerhead Ash Catcher By DiamondThe Medicali Ash Catcher with Showerhead Perc has a colored showerhead percolator and is available to order in a selection of colors. Please select your favorite color from the available option in the drop-down thực đơn when you place your order. Please note that you can select the color of the showerhead percolator, it is not possible to select the color or style of the logo. The logos come in a wide variety of colors and styles, you will receive one at random, depending on availability.

    pilot lighter
  • Dab Mat metal one hitter We have secure servers and exchange zero customer information. The glass storage jar has 2.5 mm thick sides and a super thick 7 milimet bottom. The glass has to be made to exact dimensions in order to for all the pieces to fit together correctly. .

    how to connect plastic water pipes

Leave a comment

Contact

Get in Touch

We love your feedback, Drop us a line